Hydraulic Metal Shears

the advantages of small size, lightweight, low inertia, low noise, stable movement, convenient operation, large shearing section,

and adjustment of the scissor mouth. use. Easy to operate and control, start and stop cutting at any position during the working

process, and can control the size of the cutting port arbitrarily according to the size of the material to be cut, to obtain

working benefits.

1. The shearing machine has a wide range of applications, high work efficiency, simple operation, and convenient maintenance.

The host can be installed indoors or outdoors;

2. This series of crocodile shears has a compact structure and reliable mechanical performance;

3. Working knife edge length: 500mm-1200mm, shearing force 60T-250T, suitable for different scales and different requirements

for users to choose from;

4. There is no need for foot screws for installation and diesel engine drive is optional for places without power supply.

The crocodile shears are composed of a shearing cylinder, a shearing knife, a sliding block pressing knife, a lower knife seat,

and a pressing oil cylinder. When the shearing work is running, the hydraulic pump station (power output source) supplies

oil to the pressing oil cylinder to let the slider The pressing knife is pushed to the lower knife seat to complete the fixing and

pressing of the material, and then the hydraulic pump station supplies oil to the shearing cylinder to make the shearing knife

go down to complete the shearing step. After the shearing is completed, the hydraulic pump station completes the return

action driven by the successive hydraulic oil return of the shearing cylinder and the pressing cylinder.

 

1. The shearing machine has a wide range of applications, high work efficiency, simple operation, and convenient maintenance.

The host can be installed indoors or outdoors;

2. This series of crocodile shears has a compact structure and reliable mechanical performance;

3. Working knife edge length: 500mm-1200mm, shearing force 60T-250T, suitable for different scales and different requirements

for users to choose;

4. There is no need for foot screws for installation, and diesel engine drive is optional for places without a power supply;

5. Emphasis: The blade length and shearing force of the shearing machine can be designed and manufactured according to

user requirements.

Technical force, process equipment, testing means. Over the past few years, continuous products, warm and thoughtful service

have won the trust of the majority of users.

 

Metal, iron sheet, cast iron, thin iron, thin iron sheet, light and thin material, steel, color steel tile, scrap steel, scrap iron, aluminum alloy,

channel steel, angle steel, angle iron, copper plate, metal plate, aluminum profile, scrap steel bar, aluminum plate, Iron plate, steel plate,

round steel, scrap metal

Precautions for use:

1. The equipment should be operated by a designated person, and other people are not allowed to use it arbitrarily without training.

2. Before driving, check whether all parts are normal and whether the fasteners are firm.

3. It is forbidden to cut unannealed steel parts, cast iron parts, soft metal parts, too-thin workpieces, or workpieces with a length of less

than 100 mm, and workpieces exceeding the length of the scissors.

4. During operation, the human body is not allowed to approach the transmission part of the equipment and the knife edge, and attention

should be paid to the safety of the surrounding people, as the material will tilt and hurt people. When cutting, the material should be cut

as close as possible to the inside of the knife. When cutting shorter materials, it is not allowed to use hand-held workpieces to feed materials,

and clamps should be used to feed materials.

5. When the equipment is running, the operator is not allowed to leave the post without authorization. When the work is completed or temporarily

leaves the post, the power supply should be cut off. At the same time, when the machine is running, it is not allowed to repair or touch the moving

parts with hands, and it is strictly forbidden to press the material in the material box with hands or feet.

6: Each lubricating point of the machine should be filled with lubricating oil at least once per shift.

Established in 2011, Zhengzhou Shuliy Machinery Co., Ltd has always adhered to the development concept of environmental protection, committed to the research of recycling machinery.

So far, we have produced more than 30 kinds of recycling machines, including plastic granulator machines, egg tray machines, copper wire recycling machines, shredder machines, etc. We always focus on quality throughout the whole process of production and services.

In addition, Shuliy has a group of professional technical and sales teams, who concentrate on providing customers with a complete set of production programs, giving full play to the economic value, use value, and environmental protection value of the machine, and help earning more benefits for customers. At present, Shuliy machines have been exported to the United States, Canada, Australia, Malaysia, Indonesia, South Africa, and other countries. In the future, Shuliy Group will as always create more value together with you.

With the unique effect of high automation, and stable and reliable performance, the company has won the trust and good evaluation of many customers

Hot Tags: hydraulic metal shears, China hydraulic metal shears manufacturers, suppliers, Waste Recycling Machinery, Hydraulic Metal Baler Machine, Double Shaft Machine, Metal Scrap Shearing Machine, Copper Pipe Separation Machine, Metal Steel Scrap Shredder